MAX4514ESA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4514 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 20μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4514ESA Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. Mounted in Surface Mount is this multiplexer. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. Total terminations are 8. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An injection of 8 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NO switching circuits. There are 1 circuits in this switch device. Try searching with MAX4514 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 20Ohm. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 1μA. Using a single voltage supply, this switch device consumes 2V~12V volts. A voltage higher than 1μA may cause damage to the switch multiplexer.
MAX4514ESA Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4514ESA Applications
There are a lot of Maxim Integrated MAX4514ESA Analog Switches & Multiplexers ICs applications.
- Cross Connects
- SDH/SONET multiplexers
- Fiber In The Loop (FITL)
- Cellular phones
- DSLAMs
- Channel Banks
- Audio signal routing
- Digital access cross connects
- Digital Cross-Connects
- Automotive applications