MAX4501CUK-T
| Parameters | |
|---|---|
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4501 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 29.993795mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
MAX4501CUK-T Overview
As the electronic part is packed in SC-74A, SOT-753, international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around 0°C~70°C TA is the extended operating temperature. A total of 5 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 5 series. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching with MAX4501 to find analog multiplexer variants. A 250Ohm internal resistance characterizes this multiplexer. The functions of 5 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analog switch ics with Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 2V. It would be sufficient to run this analogue multiplexer with 1μA current. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur.
MAX4501CUK-T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4501CUK-T Applications
There are a lot of Maxim Integrated MAX4501CUK-T Analog Switches & Multiplexers ICs applications.
- RGB switches
- Audio/video switches
- Cable PC
- Fiber to the Home
- DSLAMs
- Low-Voltage
- Sample hold systems
- SONET
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fault Tolerant Systems