MAX4501CSA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 250Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4501 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 125 ns |
| On-State Resistance (Max) | 250Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3pF 3pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 1pC |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4501CSA Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 8. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 8 series. A SPST - NO switching circuit is used to build these analog multiplexers. 1 circuits are used in this analogue multiplexer. Search with MAX4501 if you are looking for analog multiplexer variants. An switch multiplexer with 250Ohm internal resistance has a value of 250Ohm. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 2V. 1μA current would be enough for this multiplexer to operate. Using only a single voltage supply, this analog switch requires 2V~12V voltage. The analogue multiplexer may be damaged if voltage is greater than 1μA. Operating voltages range from 9V.
MAX4501CSA Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4501CSA Applications
There are a lot of Maxim Integrated MAX4501CSA Analog Switches & Multiplexers ICs applications.
- Cell phones
- RGB switches
- Audio/video switches
- Relay Replacement
- PBX interfaces
- Industrial and process control systems
- Public switching systems
- Industrial
- SONET/SDH ADM
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8