MAX4198EUA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| Series | Beyond-the-Rails™ |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Max Power Dissipation | 330mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4198 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Operating Supply Current | 45μA |
| Nominal Supply Current | 45μA |
| Slew Rate | 0.07V/μs |
| Amplifier Type | Differential |
| Common Mode Rejection Ratio | 70 dB |
| Voltage - Supply, Single/Dual (±) | 2.7V~7.5V ±1.35V~3.75V |
| Output Current per Channel | 5.5mA |
| Input Offset Voltage (Vos) | 100μV |
| Bandwidth | 175 kHz |
| Power Supply Rejection Ratio (PSRR) | 90dB |
| Supply Voltage Limit-Max | 8V |
| Input Bias Current | 100nA |
| Length | 3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4198EUA Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. Differential-type instrumentation amplifiers are used in this application. A Tube case is used to deliver the buffer op amp. There have been a total of 8 terminations over the past year. In this case, there are 8 pins on the board. I would like to remind you that this buffer op amp should be powered by an 5V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The op amp ic has an array of 8 pins on it. Regarding input offset voltage, buffer amplifier rates 100μV voltage. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. Using a supply current of 45μA , this buffer op amp will be able to operate. The op amp ic has 1 channels on it. A benefit of this op amp ic is that it outputs Rail-to-Rail signals, which is one of the many advantages it has to offer. The operating supply voltage of instrumentation amplifier is rated 5V voltage. Buffer op amp series numbers are indicated by the Beyond-the-Rails?.
MAX4198EUA Features
8 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
MAX4198EUA Applications
There are a lot of Maxim Integrated MAX4198EUA Instrumentational OP Amps applications.
- Inverse/same-phase proportional circuit
- Video computer boards
- Information processing
- Blood pressure sensors
- Power control
- Hand-held batteries
- Car stereo
- Power generator
- Portable electronic products powered by batteries
- High-frequency data acquisition systems