MAX4066CEE
| Parameters | |
|---|---|
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2V~16V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 45Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 150 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 185 ns |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 45Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -86dB @ 1MHz |
| Switch-on Time-Max | 125ns |
MAX4066CEE Overview
Packed in 16-SSOP (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. A total of 16 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. SPST - NO switching circuits are used in these analog switch ics. The multiplexer consists of 4 circuits. Try searching for the analog switch ic with MAX4066 if you are looking for variants. Internally, this switch multiplexer has a resistance of 45Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. Digital switch that provides Single power at a cost-effective price. It is recommended to use 2V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 1μA. This analog switch requires a voltage of 2V~16V to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4066CEE Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 100MHz
MAX4066CEE Applications
There are a lot of Maxim Integrated MAX4066CEE Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Residential Gateways, Home Gateway/Router
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical
- CSU
- RGB switches
- Audio and video signal routing
- Cable PC
- Multiplexers
- SONET/SDH ADM