MAX3483ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| HTS Code | 8542.39.00.01 |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX3483 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3V |
| Supply Current-Max | 2.2mA |
| Data Rate | 250kbps |
| Output Characteristics | 3-STATE |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 50mV |
| Interface Standard | EIA-422; EIA-485 |
| Receive Delay-Max | 120 ns |
| Transmit Delay-Max | 1400 ns |
| Output Low Current-Max | 0.0025A |
| Out Swing-Min | 1.5 V |
| High Level Input Current-Max | 0.000002A |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
MAX3483ESA+T Overview
This driver chip is excellent for driving common LEDs due to its enhanced 8-SOIC (0.154, 3.90mm Width) package.In the Tape & Reel (TR) package, this receiver is mounted.The Transceiver can transceiver technology has enabled this part to power many solutions for a variety of uses.You can place this wide receiver to any Surface Mount-type PCB or development board.This differential driver consumes 3V~3.6V for its power supplyIt is possible to have up to 1/1 receivers/drivers in use simultaneously with this electronic part.Applications with operating temperatures of -40°C~85°C have been designed primarily for this ic receiver.There is a voltage range of 3.3V for this line driver ic, so it can operate efficiently.Wide receiver has 8 terminations built in for driving or receiving signals from data.The transceiver is packaged with 8 market standard pinouts so that it can be easily used.As the base part number MAX3483 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.It is important to note that this ic receiver had a maximum resolution of 1 bits.In most cases, the receiver will be specified with a 1-bit resolution.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.An 8-pin power supply is provided by this driver IC, which allows it to operate from an 3.3V-pin power supply.The optical transceiver module's VCC pin should receive enough input current, but not more than 2.2mA.
MAX3483ESA+T Features
Tape & Reel (TR) package
8 pin count
3.3V power supply
MAX3483ESA+T Applications
There are a lot of Maxim Integrated MAX3483ESA+T Drivers/Receivers/Transceivers applications.
- Long-distance fiber optic network applications
- Thermal management
- Satellite ground stations
- Car alarm systems
- Changeing the frequency from IF to RF
- Point-to-point networking
- interconnection between computers
- Wireless HD Photography
- Tuner
- Desktop PC