MAX324CSA+T
| Parameters | |
|---|---|
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX324 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 240 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Voltage - Supply, Single (V+) | 2.7V~16V |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1998 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
MAX324CSA+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around 0°C~70°C TA. In total, 8 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. There is an electrical component included in the 8 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. This multiplexer is composed of 2 circuits. Try searching with MAX324 to find analog multiplexer variants. This digital multiplexer has 60Ohm internal resistance. For functions related to 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16V. A analog switch ic that has a cost-effective Single supply type. There should be 2.7V voltage fed to the electrical part below 2.7V. For this digital switch to work, 1μA current would suffice. Analogue multiplexers require a 2.7V~16V voltage to drain from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
MAX324CSA+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX324CSA+T Applications
There are a lot of Maxim Integrated MAX324CSA+T Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Data switching
- Communication systems
- Automatic test equipment
- Automotive applications
- Medical Instrumentation
- DVD-R
- Sample hold systems
- Cell phones
- Isolation