MAX306CPI+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Number of Pins | 28 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin (Sn) |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX306 |
| Pin Count | 28 |
| Operating Supply Voltage | 28V |
| Number of Channels | 16 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 500μA |
| Nominal Supply Current | 16μA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 130pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Height | 4.45mm |
| Length | 37.34mm |
| Width | 14.61mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX306CPI+ Overview
Packed in 28-DIP (0.600, 15.24mm), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Through Hole. There is 16:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. Total terminations are 28. A electrical component with 16 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electronic part body is injected with 28 pins. This multiplexer is composed of 1 circuits. Look for analog switch ic variants by searching with MAX306. A 100Ohm internal resistance characterizes this multiplexer. Datasheets for 28 pin functions are available upon request. In a normalsituation, users should not supply the switches with voltage higher than 30V. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 5V. 500μA current would be enough for this multiplexer to operate. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. 28V operating voltages are supported by the electronic component.
MAX306CPI+ Features
16 Channels
500μA Supply Current
MAX306CPI+ Applications
There are a lot of Maxim Integrated MAX306CPI+ Analog Switches & Multiplexers ICs applications.
- HDTV
- Central office
- Audio and video routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Sample-and-hold systems
- Routers
- Cross Connects
- ATM
- Cell phones
- Digital access cross connects