MAX13443EASA+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 506.605978mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Line Driver or Receivers |
| Technology | BICMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX13443 |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Power Supplies | 5V |
| Interface | RS-422, RS-485 |
| Operating Supply Current | 10mA |
| Propagation Delay | 2 μs |
| Supply Current-Max | 30mA |
| Data Rate | 10Mbps |
| Differential Output | YES |
| Protocol | RS422, RS485 |
| Input Characteristics | DIFFERENTIAL |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Receiver Number of Bits | 1 |
| Duplex | Half |
| Receiver Hysteresis | 25mV |
| Number of Transceivers | 1 |
| Transmit Delay-Max | 60 ns |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX13443EASA+ Overview
With the enhanced 8-SOIC (0.154, 3.90mm Width) package, this driver IC is excellent for driving common LEDs.The package of this receiver is Tube.The Transceiver can transceiver type enables this part to be used in a wide range of applications.This wide receiver can be placed on any Surface Mount-type PCB or development board.Power supply requirements for this differential driver are 4.75V~5.25V.As many as 1/1 receivers/drivers are eligible for use on this electronic part.As its name implies, this ic receiver is designed for applications where -40°C~125°C is the operating temperature.There is a voltage range of 5V for this line driver ic, so it can operate efficiently.Integrated into this wide receiver are 8 terminations that are used for driving and receiving signals from data.Transceiver comes with 8 standard pinouts that meet the market's requirements.As the base part number MAX13443 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.An enhanced power dissipation driver IC with 8 pins.Package size is drastically reduced by downsizing ICs and mounting them in high-density Surface Mount arrays.It provided a 1-bit resolution capability with this ic receiver.It is typical for this receiver to have a resolution of 1 bits when it is specified.This transceiver module is designed to operate from an input voltage supply of 5V.A rf transceiver module named Line Driver or Receivers belongs to this subcategory.Driver ICs are designed to work with a 5V power supply and this driver IC is one of them.The module isolated transceiver implements a total of 1 transceivers.There should be enough current supplied to the VCC pin of the part, but not more than 30mA.There is no matter what the input voltage is. The integrating circuit is able to drive LEDs with an input voltage of 10mA.
MAX13443EASA+ Features
Tube package
8 pin count
8 pins
5V power supply
MAX13443EASA+ Applications
There are a lot of Maxim Integrated MAX13443EASA+ Drivers/Receivers/Transceivers applications.
- Structural bonding
- Wireless access points
- Vehicle
- Gigabit Ethernet
- transmission relay
- Portable radio
- Thermal management
- Satellite ground stations
- Fiber optic cable connection network
- Remote controls