M4A3-32/32-12VNI
| Parameters | |
|---|---|
| Min Supply Voltage | 3V |
| Number of I/O | 32 |
| Memory Type | EEPROM |
| Propagation Delay | 12 ns |
| Number of Gates | 1250 |
| Max Frequency | 83.3MHz |
| Number of Programmable I/O | 224 |
| Output Function | MACROCELL |
| Number of Macro Cells | 32 |
| JTAG BST | YES |
| Voltage Supply - Internal | 3V~3.6V |
| Height Seated (Max) | 1.2mm |
| Length | 10mm |
| Width | 10mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 44-TQFP |
| Number of Pins | 44 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tray |
| Published | 1998 |
| Series | ispMACH® 4A |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 44 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | YES |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.8mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | M4A3-32 |
| Pin Count | 44 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3.3V |
| Programmable Type | In System Programmable |
| Max Supply Voltage | 3.6V |
M4A3-32/32-12VNI Overview
32 macrocells are present in the mobile phone network, which offer radio coverage from a high-power cell tower, antenna, or mast.It is embedded in the 44-TQFP package.In this case, there are 32 I/Os programmed.It is programmed that device terminations will be 44 .This electrical part has a terminal position of QUADand is connected to the ground.It is powered by a voltage of 3.3V volts.This part is in the family [0].Package the chip by Tray.In order to ensure the reliability of the device, it is designed to operate at a temperature of [0].There should be a Surface Mounton the chip.In FPGA terms, it is a type of ispMACH? 4Aseries FPGA.There are 44pins on the chip.If you use this device, you will also find [0].M4A3-32contains its related parts.As a building block for digital circuits, there are 1250gates.High efficiency requires a voltage supply of [0].It is recommended that data be stored in [0].In this case, Surface Mountis used to mount the electronic component.The 44pins are designed into the board.With a maximum supply voltage of [0], it operates.It operates with the minimal supply voltage of 3V.A total of 224 Programmable I/Os are available.It is recommended that the maximal frequency be lower than 83.3MHz.
M4A3-32/32-12VNI Features
44-TQFP package
32 I/Os
The operating temperature of -40°C~85°C TA
44 pin count
44 pins
M4A3-32/32-12VNI Applications
There are a lot of Lattice Semiconductor Corporation M4A3-32/32-12VNI CPLDs applications.
- Synchronous or asynchronous mode
- Page register
- SUPERVISORY FUNCTION (LVD AND WATCHDOG)
- Parity generators
- Handheld digital devices
- D/T registers and latches
- Programmable polarity
- ON-CHIP OSCILLATOR CIRCUIT
- Wide Vin Industrial low power SMPS
- Reset swapping