LM5033SDX
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.8mm |
| Base Part Number | LM5033 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Type | PWM Signal |
| Operating Supply Voltage | 9.6V |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1.5A |
| Voltage - Supply (Vcc/Vdd) | 15V~90V |
| Output Power | 500W |
| Control Features | Frequency Control, Soft Start |
| Topology | Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 200kHz 600kHz |
| Input Voltage (Max) | 90V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 16ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 16 ns |
| Switcher Configuration | SINGLE |
| Max Frequency | 1MHz |
| Output Phases | 1 |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
LM5033SDX Overview
With a 10-WDFN Exposed Pad package, the switching controller is suitable for a wide range of applications. dc motor controller is suitable for 2 output generation. Tape & Reel (TR) is the solid enclosure in which PMIC is packaged. PWM Signal dc switching's outputs (s) are supported. This dc control operates at 15V~90V and has a 15V~90V supply voltage. Qualified to work in an dc switcher with -40°C~125°C TJ. In this switching controller, the switch can be set to 200kHz 600kHz. As it has a Surface Mount value, it can be used for general dc dc regulator. To provide efficient switching control, Frequency Control, Soft Start is included in the dcdc regulator. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. A switching converters's terminal (s) sits at the DUAL position. The 10 terminations can be used for a wide range of dc switching. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. DC switcher's input voltageis set to 48V. You can find other relevant dc to dc converter ics by searching "LM5033". There are a total of 10 pins on switching converter. There is a particular type of Switching Regulator or Controllers in switching converter. This dc to dc regulator accepts only 90V input voltage at most. If you are starting a new project, you should note the dc dc regulator's typical output current is 1.5A. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. DC regulator's maximum frequency is 1MHz. Users should apply 9.6V to operate the voltage regulator dc to dc safely and reliably.
LM5033SDX Features
PWM Signal Outputs
Switching Frequency: 200kHz 600kHz
Frequency Control, Soft Start
PULSE WIDTH MODULATION
LM5033SDX Applications
There are a lot of Texas Instruments LM5033SDX DC to DC converter applications.
- Hydrogen power
- Various precision measuring instruments
- Serial communication converter
- Window air conditioners
- Digital display device
- Nuclear power plants
- Production lines
- Domestic water pumps
- CMM
- Current source circuits