LM5033SD
| Parameters | |
|---|---|
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-WDFN Exposed Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.8mm |
| Frequency | 225kHz |
| Base Part Number | LM5033 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Type | PWM Signal |
| Operating Supply Voltage | 9.6V |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1.5A |
| Voltage - Supply (Vcc/Vdd) | 15V~90V |
| Quiescent Current | 150μA |
| Output Power | 500W |
| Control Features | Frequency Control, Soft Start |
| Topology | Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 200kHz 600kHz |
| Input Voltage (Max) | 90V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 16ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 16 ns |
| Switcher Configuration | SINGLE |
| Output Phases | 1 |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Width | 4mm |
LM5033SD Overview
The switching controller fits in the 10-WDFN Exposed Pad package and is ideal for most applications. dc motor controller is suitable for 2 output generation. A solid enclosure of Tape & Reel (TR) surrounds pmic. PWM Signal dc switching's outputs (s) can be handled by it. Voltages 15V~90V are the dc control's supply voltage and operating voltage, respectively. Worked in an dc switcher with a -40°C~125°C TJ rating. This switching controller can switch at 200kHz 600kHz. The Surface Mount makes it ideal for general dc dc regulator. Featured in the dcdc regulator is Frequency Control, Soft Start which allows efficient switching control. Switch converters are connected to ICs with SWITCHING CONTROLLER analog outputs. The switching converters's terminals (s) are designed at DUAL. The 10 terminations can be used for a wide range of dc switching. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 48V. A search for "LM5033" will reveal other relevant dc to dc converter ics. Pins number 10 of switching converter in total. In particular, switching converter is a type of Switching Regulator or Controllers. The dc to dc regulator is limited to 90V input voltage. If you start a project, note down the dc dc regulator's usual output current of 1.5A. DC switcher's Surface Mount qualifies it for most applications and prototypes. There is 225kHz frequency setting on the switching controller. In order for the voltage regulator dc to dc to perform safely and reliably in a circuit, users are advised to apply 9.6V. DC switching uses 150μA when it is dormant.
LM5033SD Features
PWM Signal Outputs
Switching Frequency: 200kHz 600kHz
Frequency Control, Soft Start
PULSE WIDTH MODULATION
Frequency: 225kHz
LM5033SD Applications
There are a lot of Texas Instruments LM5033SD DC to DC converter applications.
- Automatic plug-in machines
- Television equipment
- Bending machines
- Lathes
- Adjustable voltage or current linear circuits
- Smoke prevention equipment
- Laboratories
- Program control systems
- Industrial robots
- Post equipment