LM224DR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -25°C~85°C |
| Packaging | Cut Tape (CT) |
| Published | 2010 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | LM224 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 16V |
| Number of Elements | 4 |
| Power Supplies | 5/30V |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 1.2mA |
| Output Current | 40mA |
| Slew Rate | 0.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 90nA |
| Voltage - Supply, Single/Dual (±) | 3V~32V ±1.5V~16V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 5mV |
| Gain Bandwidth Product | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.3μA |
| Power Supply Rejection Ratio (PSRR) | 65dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.15μA |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
LM224DR2 Overview
In the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. This is a General Purpose type op amp. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. A total of 14 terminations have been reported in the past few weeks. A total of 14 pins are attached to buffer op amp. Please take in mind that op amp should be run at 5V. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. An 14-pin op amp ic is included in the package. With regard to input offset voltage, instrumentation amplifier is rated at 5mV. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -25°C~85°C as far as operating temperature is concerned. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.4mA and 10 . Voltage gain should remain at 100dB. There are 4 elements in total in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 16V. It is used TAPE AND REEL to pack the op amps.
LM224DR2 Features
14 Pins
supply voltage of 5V
100dB voltage gain
LM224DR2 Applications
There are a lot of ON Semiconductor LM224DR2 Instrumentational OP Amps applications.
- Band-stop filter
- Tablets
- Multiplication circuits
- Video computer boards
- Subtraction operation circuits
- Integrator circuits
- Vehicle electronics
- Proportional operation circuits
- Automatic control
- Large motor controllers