ICL7632ECPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ICL7632 |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Power Supplies | +-1/+-8/2/16V |
| Number of Circuits | 3 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 15μA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±1V~8V |
| Input Offset Voltage (Vos) | 20mV |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 44 kHz |
| Voltage Gain | 90dB |
| Average Bias Current-Max (IIB) | 0.004μA |
| Low-Offset | NO |
| Frequency Compensation | YES AVCL>=20 |
| Supply Voltage Limit-Max | 9V |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | YES |
| Height Seated (Max) | 4.572mm |
| Length | 19.175mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ICL7632ECPE Overview
Packaged in a 16-DIP (0.300, 7.62mm) case, the buffer op amp is ready to use. General Purpose-type instrumentation amplifiers are used in this application. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. A total of 16 terminations have been reported in the past few weeks. Buffer amplifier has a total of 16 pins. It is important to remember that this op amp should be operated at a voltage of 5V volts. Instrumentation amplifier is a part of Operational Amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 20mV. This electronic part is best mounted with type Through Hole. With regard to operating temperature, this op amp functions well at 0°C~70°C. Operational amplifier can operate supply current at 1mA. Voltage gain should remain at 90dB. On this instrumentation amplifier, there are 3 circuits that are connected together. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 8V.
ICL7632ECPE Features
16 Pins
supply voltage of 5V
90dB voltage gain
Output Type: Rail-to-Rail
ICL7632ECPE Applications
There are a lot of Maxim Integrated ICL7632ECPE Instrumentational OP Amps applications.
- Instrumentation
- Integrator circuits
- Scintillation detectors
- Semiconductor detectors
- RF cable systems
- Switching amplifier
- Fast A/D and D/A converters
- Portable docking station
- Signal amplification
- Automation control systems