ICL7612DCSA+
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ICL7612 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Circuits | 1 |
| Current - Supply | 1mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2V~16V ±1V~8V |
| Gain Bandwidth Product | 1.4MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 44 kHz |
| Average Bias Current-Max (IIB) | 0.004μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 9V |
| Voltage - Input Offset | 15mV |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.00005μA |
| Programmable Power | YES |
| Neg Supply Voltage-Max (Vsup) | -9V |
| Voltage Gain-Min | 4000 |
| Length | 4.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ICL7612DCSA+ Overview
Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case. Op amps are General Purpose types of amplifier on the chip. A Tube case is used to deliver the buffer op amp. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. As a reminder, this buffer op amp should be powered by 5V battery and that the battery should be inserted in the amplifier. Instrumentation amplifier is a part of Operational Amplifier. This electrical part should be mounted using type Surface Mount. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. On this buffer amplifier, there are 1 circuits. One of the many benefits of this op amp ic is that it emits Rail-to-Rail signals. As a result, it is recommended that a power supply of 1mA be used with this electronic part. A minimum voltage gain of 4000 is the minimum voltage gain that this instrumentation amplifier is capable of producing.
ICL7612DCSA+ Features
8 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
ICL7612DCSA+ Applications
There are a lot of Maxim Integrated ICL7612DCSA+ Instrumentational OP Amps applications.
- Proportional operation circuits
- Television
- Micro signal measurement
- Video amplifiers
- Addition operation circuits
- Automation control systems
- Measurements of Wheatstone bridge
- Scintillation detectors
- Communication
- Polarized electrodes