FSA5157L6X
| Parameters | |
|---|---|
| Factory Lead Time | 5 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Weight | 30g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 360mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 1 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA5157 |
| Output | SEPARATE OUTPUT |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 30nA |
| Power Dissipation | 180mW |
| Max Supply Current | 100nA |
| Number of Bits | 2 |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 80MHz |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 360mOhm Typ |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 21pF |
| On-state Resistance Match-Nom | 0.12Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 55ns, 30ns |
| Charge Injection | 6pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 500μm |
| Length | 1.45mm |
| Width | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
FSA5157L6X Overview
The electrical component comes in 6-UFDFN packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there have been 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. A 2.3V voltage supply should turn on and run the electronic component. A SPDT switching circuit is used for these analog switches. FSA5157 can be used to search for analog multiplexer variants. It has an internal resistance of 360mOhm. The functions of 6 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. 1.65V should be the lowest voltage fed to the electronic component. Using only a single voltage supply, this analog switch requires 1.65V~4.3V voltage. The analogue multiplexer may be damaged if voltage is greater than 100nA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The 1 inputs need to be operated in order to work. 80MHz bandwidths enable data to be transferred. The switch device is capable of conducting in a 2-bit mode.
FSA5157L6X Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 80MHz
2-Bit
FSA5157L6X Applications
There are a lot of ON Semiconductor FSA5157L6X Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Data Acquisition Systems
- Channel Banks
- Voice over IP/DSL – Integrated Access Devices, Smart
- SDH
- Fiber to the Home
- Avionics test equipment
- Video signal routing
- Private Branch Exchange (PBX)
- Automotive applications