FSA4157AP6X
| Parameters | |
|---|---|
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 1.15Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 180mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 4.5V |
| Base Part Number | FSA4157 |
| Number of Outputs | 2 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100nA |
| Power Dissipation | 180mW |
| Max Supply Current | 500nA |
| Turn On Delay Time | 60 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 20 ns |
| On-State Resistance (Max) | 1.15Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 2nA Typ |
| Channel Capacitance (CS(off), CD(off)) | 12pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 35ns, 15ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
FSA4157AP6X Overview
As the electronic part is packed in 6-TSSOP, SC-88, SOT-363, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Temperatures around -40°C~85°C TA are extended for operation. There are 6 terminations totally. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 4.5V is used, the electronic component should be turned on and run. A SPDT switching circuit is used for these analog switches. Try searching for the analog switch ic with FSA4157 if you are looking for variants. A 1.15Ohm internal resistance characterizes this multiplexer. To find out what the functions of 6 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. It is recommended to use 2.7V as the lowest voltage for the electrical part. An analogue multiplexer drains from a single voltage supply at 2.7V~5.5V. Putting voltage greater than 500nA on the multiplexer may cause damage. A 300MHz-bandwidth can be used for data transfer. An output of 2 is provided by the digital multiplexer.
FSA4157AP6X Features
1 Channels
Switch Circuit: SPDT
Bandwidth: 300MHz
FSA4157AP6X Applications
There are a lot of ON Semiconductor FSA4157AP6X Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Precision test equipment
- Data switching
- High reliability control systems
- Power routing
- Audio signal routing
- MP3 players
- Access Concentrators
- Channel Banks
- Microprocessor controlled systems