FSA266K8X
| Parameters | |
|---|---|
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-VFSOP (0.091, 2.30mm Width) |
| Number of Pins | 8 |
| Weight | 30mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA266 |
| Output | SEPARATE OUTPUT |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Nominal Supply Current | 1μA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 10 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 10.5 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.2ns, 4.1ns |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -70dB @ 10MHz |
| Switch-on Time-Max | 5.6ns |
| Switch-off Time-Max | 6.9ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 700μm |
| Length | 2mm |
| Width | 2.3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
FSA266K8X Overview
As the electronic part is packed in 8-VFSOP (0.091, 2.30mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, 8 terminations have occurred. Due to its 2 channels, the electrical component produces high-quality output. With a 2.3V voltage supply, the electrical component should be turned on and run. These analog multiplexers are built based on SPST - NO switching circuits. FSA266 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 10Ohm. Please refer to the datasheets for 8 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.65V. An analogue multiplexer drains from a single voltage supply at 1.65V~5.5V. The analogue multiplexer may be damaged if voltage is greater than 1μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. In 300MHz-bandwidths, data can be transferred.
FSA266K8X Features
2 Channels
Switch Circuit: SPST - NO
Bandwidth: 300MHz
FSA266K8X Applications
There are a lot of ON Semiconductor FSA266K8X Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Audio and video signal routing
- E1 Network Equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- High reliability control systems
- High-Voltage
- Power routing
- Intelligent PBX
- High speed data transmission line cards
- Digital Cross-Connects