FSA2467UMX
| Parameters | |
|---|---|
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Number of Functions | 2 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 0.4mm |
| Base Part Number | FSA2467 |
| Output | SEPARATE OUTPUT |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Max Supply Current | 100nA |
| Turn On Delay Time | 80 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 52 ns |
| -3db Bandwidth | 85MHz |
| On-State Resistance (Max) | 400Ohm Typ |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 32pF |
| On-state Resistance Match-Nom | 0.03Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 50ns, 32ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω (Min) |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height Seated (Max) | 0.55mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-UFQFN |
| Number of Pins | 16 |
| Weight | 6.54mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
FSA2467UMX Overview
Shipping overseas is convenient with the electronic component packed in 16-UFQFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:2. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. Due to its 2 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 2.3V, it should be turned on and run. Unlike digital switches, these are based on DPDT switching circuits. The multiplexer consists of 2 circuits. Try searching for the analog switch ic with FSA2467 if you are looking for variants. A 400Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 4.3V. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage the electrical component should receive. A voltage of 1.65V~4.3V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 100nA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
FSA2467UMX Features
2 Channels
Switch Circuit: DPDT
-3db Bandwidth: 85MHz
FSA2467UMX Applications
There are a lot of ON Semiconductor FSA2467UMX Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Sample hold systems
- Video switching
- Cell phones
- Wireless Local Loop
- Digital cross connects (DSX-1)
- Video signal routing
- Precision test equipment
- Microprocessor controlled systems
- Cable PC