FSA2258L10X
| Parameters | |
|---|---|
| Max Supply Current | 100nA |
| Turn On Delay Time | 65 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 500mOhm Typ |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 3.3pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 55ns, 30ns |
| Charge Injection | 25pC |
| Channel-to-Channel Matching (ΔRon) | 80m Ω |
| Crosstalk | -100dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Drain to Source Resistance | 1.5Ohm |
| Height | 500μm |
| Length | 2.1mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 6 Weeks |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 26mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 500mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BUTT |
| Number of Functions | 2 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | FSA2258 |
| Number of Outputs | 4 |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Analog IC - Other Type | SPST |
| Nominal Supply Current | 80nA |
FSA2258L10X Overview
The electrical component comes in 10-UFQFN Exposed Pad packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operational temperature extended around -40°C~85°C TA. In total, 10 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. An 3.3V voltage supply should allow the electrical part to be turned on and run. Circuits based on SPDT switching are used to construct these analog switch ics. Search with FSA2258 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 500mOhm. To find out what the 10 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 4.3V. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 1.65V. A voltage of 1.65V~4.3V is required to drain this analog switch from a single voltage supply. If put voltage greater than 100nA on the device, damage may be caused to the analogue multiplexer. An analog IC with the number SPST is integrated into this board. Among the inputs that can be operated are the 2 inputs. There is 1.5Ohm Drain to Source resistance on this electronic part. An output of 4 is provided by the digital multiplexer.
FSA2258L10X Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 50MHz
Drain-to-Source resistance: 1.5Ohm
FSA2258L10X Applications
There are a lot of ON Semiconductor FSA2258L10X Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- E1 Multiplexer
- Relay replacements
- Microprocessor Controlled Analog Systems
- Intelligent PBX
- Cellular phones
- DSLAMs
- Audio signal routing
- High reliability control systems
- Medical systems