EPM7160EQC160-15
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | PQFP |
| Number of Pins | 160 |
| Published | 1998 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Moisture Sensitivity Level (MSL) | 3 |
| Number of Terminations | 160 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| Additional Feature | CONFIGURABLE I/O OPERATION WITH 3.3V OR 5V |
| HTS Code | 8542.39.00.01 |
| Subcategory | Programmable Logic Devices |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 220 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 100MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 160 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 5V |
| Temperature Grade | COMMERCIAL |
| Max Supply Voltage | 5.25V |
| Min Supply Voltage | 4.75V |
| Number of I/O | 104 |
| Memory Type | EEPROM |
| Propagation Delay | 15 ns |
| Frequency (Max) | 100MHz |
| Programmable Logic Type | EE PLD |
| Number of Gates | 3200 |
| Number of Programmable I/O | 104 |
| Number of Logic Blocks (LABs) | 10 |
| Output Function | MACROCELL |
| Number of Macro Cells | 160 |
| JTAG BST | NO |
| In-System Programmable | NO |
| Height Seated (Max) | 4.07mm |
| Length | 28mm |
| Width | 28mm |
| RoHS Status | RoHS Compliant |
EPM7160EQC160-15 Overview
There are 160 macro cells in the network, which are high-power cell sites that provide radio coverage (tower, antenna, or mast) for a mobile phone network.It is part of the PQFP package.There are 104 I/Os on the board.Terminations of devices are set to [0].As the terminal position of this electrical part is [0], it serves as an important access point for passengers or freight.A voltage of 5Vprovides power to the device.It belongs to the family [0].With 160pins programmed, the chip is ready to use.This device is also capable of displaying [0].A digital circuit can be constructed using 3200gates.A high level of efficiency can be achieved by maintaining the supply voltage at [0].EEPROM is adopted for storing data.This device is mounted by Surface Mount.It is designed with 160 pins.This device operates at a voltage of 5.25V when the maximum supply voltage is applied.A minimum supply voltage of 4.75V is required for it to operate.A programmable I/O count of 104 has been recorded.This can be achieved at a frequency of 100MHz.It is recommended that the operating temperature be higher than 0°C.It is recommended that the operating temperature be lower than 70°C.It consists of 10 logic blocks (LABs).The maximum frequency should not exceed 100MHz.In programmable logic, a type of logic can be categorized as EE PLD.
EPM7160EQC160-15 Features
PQFP package
104 I/Os
160 pin count
160 pins
10 logic blocks (LABs)
EPM7160EQC160-15 Applications
There are a lot of Altera EPM7160EQC160-15 CPLDs applications.
- ROM patching
- Digital multiplexers
- Reset swapping
- I/O PORTS (MCU MODULE)
- TIMERS/COUNTERS
- Voltage level translation
- Power up sequencing
- Synchronous or asynchronous mode
- DMA control
- I/O expansion