EL4543IUZ
| Parameters | |
|---|---|
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Package / Case | QSOP |
| Number of Pins | 24 |
| Published | 2003 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 |
| Number of Terminations | 24 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Line Driver or Receivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Qualification Status | Not Qualified |
| Max Output Current | 60mA |
| Operating Supply Voltage | 9V |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 14.5mA |
| Nominal Supply Current | 16.2mA |
| Max Supply Current | 16.2mA |
| Current - Output | 50A |
| Slew Rate | 1000 V/μs |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 10μA |
| Output Current per Channel | 60mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 350MHz |
| Gain Bandwidth Product | 350MHz |
| Differential Output | YES |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Input Characteristics | DIFFERENTIAL |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 350MHz |
| Interface IC Type | LINE DRIVER |
| Driver Number of Bits | 3 |
| Min Dual Supply Voltage | 2.5V |
| Dual Supply Voltage | 5V |
| Interface Standard | GENERAL PURPOSE |
| Height | 1.42mm |
| Length | 8.66mm |
| Width | 3.91mm |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
EL4543IUZ Overview
Packaged in a QSOP case, the buffer op amp is ready to use. During the past two weeks, there have been close to 24 terminations. Please take in mind that op amp should be run at 5V. It should be noted that this op amp is a type of Line Driver or Receivers device. It has 24 pins that make up the linear amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 10mV. Operational amplifier can operate supply current at 14.5mA. A linear amplifier like this has 3 circuits on it. Using this buffer op amp requires a temperature of at least -40°C. Use op amps only at temperatures no higher than 85°C. The operating supply voltage of instrumentation amplifier is rated 9V voltage. I would like to point out that this electrical component is capable of working from a voltage below 12V as far as the power supply is concerned. A high supply voltage of more than 5V is recommended for the instrumentation amplifier's supply voltage. This electronic part should be conducted with a dual supply voltage of 6V volts for this part. Op amp's interface IC type can be classified as LINE DRIVER.
EL4543IUZ Features
supply voltage of 5V
EL4543IUZ Applications
There are a lot of Intersil (Renesas Electronics America) EL4543IUZ Instrumentational OP Amps applications.
- Polarized electrodes
- Signal transformation
- Biopotential
- Video conversion and routing
- Home audio systems
- Medical instruments
- High input resistance broadband
- Logarithmic operation circuits
- Computer workstations
- Gaming industry