DG9232DY-E3
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 30Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG9232 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 75 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 30Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF 13pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 75ns, 50ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
DG9232DY-E3 Overview
This electronic part is conveniently packaged in 8-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, there are 8 terminations. This electronic part offers high-quality output due to its 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 8 pins. Based on SPST - NC switching circuits, these analog multiplexers work. Use DG9232 to search for variants of the digital switches. A 30Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. The analog switch ic is of the Single supply type and is cost-effective. 2.7V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. An analogue multiplexer drains from a single voltage supply at 2.7V~12V. Put voltage above 1μA on the multiplexer to cause damage. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. Operating 2 inputs is required.
DG9232DY-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG9232DY-E3 Applications
There are a lot of Vishay Siliconix DG9232DY-E3 Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- Power routing
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- SONET
- HDTV
- Cell phones
- Data Acquisition Systems
- Sample-and-hold systems
- SDH/SONET multiplexers
- Communication systems