DG613AEQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 72Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATE WITH 5V AND 3V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | DG613 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 450mW |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 55 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±2.7V~5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -3V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 5V |
| -3db Bandwidth | 720MHz |
| On-State Resistance (Max) | 115Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 3pF |
| On-state Resistance Match-Nom | 0.7Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 55ns, 35ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 700m Ω |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 50ns |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG613AEQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~125°C TA. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. This electrical component is included in the 16 series of products. Unlike digital switches, these are based on SPST - NO/NC switching circuits. Try searching with DG613 if you're looking for variants. An switch multiplexer with 72Ohm internal resistance has a value of 72Ohm. Datasheets for functions of 16 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 2.7V. It would be sufficient to run this analogue multiplexer with 1μA current. The analogue multiplexer may be damaged if voltage is greater than 100μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5V. With dual power supplies, you should attach at least 2.7V. There are SEPARATE OUTPUT outputs on this analog switch ic. The electrical component supports 4 inputs. Don't forget the additional features of this electronic part, such as: ALSO OPERATE WITH 5V AND 3V SUPPLY.
DG613AEQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 720MHz
Additional Features: ALSO OPERATE WITH 5V AND 3V SUPPLY
DG613AEQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG613AEQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video signal routing
- Cable Modem
- Communication systems
- 65 V DACs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- ATM
- ISDN NT1/TA
- Access Concentrators