DG442LDQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | PURE MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG442 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 30nA |
| Power Dissipation | 450mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 35 ns |
| Max Dual Supply Voltage | 6V |
| -3db Bandwidth | 280MHz |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 6pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -95dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Drain to Source Resistance | 17Ohm |
| Normal Position | NO |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG442LDQ-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. 16 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. A SPST - NO switching circuit is used for these analog switches. Using the DG442 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 35Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 2.7V. For this digital switch to work, 10μA current would suffice. A digital multiplexer may suffer damage if voltage is applied above 1μA. There is no problem with using dual supply voltage, but it should not exceed 6V. For dual power supplies, a voltage of at least 3V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Among the inputs that can be operated are the 4 inputs. Resistivity from Drain to Source is 17Ohm for this electronic part.
DG442LDQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
-3db Bandwidth: 280MHz
Drain-to-Source resistance: 17Ohm
DG442LDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG442LDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Video switching
- Fiber to the Home
- Low-Voltage
- Power routing
- Cable PC
- Automatic test equipment
- Sample-and-hold systems
- SDH/SONET multiplexers
- 65 V DACs
- Voice over IP/DSL – Integrated Access Devices, Smart