DG418LDY-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 20Ohm |
| Terminal Finish | TIN LEAD |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 41 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 32 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 43ns, 31ns |
| Charge Injection | 1pC |
| Crosstalk | -71dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 44ns |
| Switch-off Time-Max | 33ns |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG418LDY-T1 Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around -40°C~85°C TA is the extended operating temperature. 8 terminations have been made so far. A 1 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 8 pins. SPST - NO switching circuits are used in these analog switch ics. This digital multiplexer has 20Ohm internal resistance. Datasheets for functions of 8 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 12V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. 2.7V is the lowest voltage the electrical component should receive. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 6VA dual power supply should have at least 3V voltage attached. In order to operate the 1 inputs, there are several steps to follow. This electronic part has additional features, such as: VIDEO APPLICATION.
DG418LDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: VIDEO APPLICATION
DG418LDY-T1 Applications
There are a lot of Vishay Siliconix DG418LDY-T1 Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Fault Tolerant Systems
- USB 1.1 signal switching circuits
- Audio signal routing
- Multiplexers
- Automatic test equipment
- RGB switches
- Mechanical reed relay replacement
- Remote Powered Equipment
- Audio and video routing