DG333ALDW-E3
| Parameters | |
|---|---|
| Factory Lead Time | 12 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 800.987426mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2017 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 75Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG333 |
| Pin Count | 20 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 200μA |
| Power Dissipation | 800mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 5V~40V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 45Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 2.34mm |
| Length | 12.8mm |
| Width | 7.49mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG333ALDW-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 20-SOIC (0.295, 7.50mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. There are 20 terminations totally. This electronic part offers high-quality output due to its 4 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. A total of 20 pins are injected into the body of the electronic part. A SPDT switching circuit is used to build these analog multiplexers. A 1 circuit is present in this switch device. Try searching with DG333 to find analog multiplexer variants. A 75Ohm internal resistance characterizes this multiplexer. Datasheets for 20 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 40V. The digital multiplexer has a low cost Dual, Single supply. 5V should be the lowest voltage fed to the electronic component. An operating current of 200μA would be sufficient for this switch device. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 22V. A dual power supply should have at least 4V voltage attached. 8 outputs are included in the analogue multiplexer.
DG333ALDW-E3 Features
4 Channels
Switch Circuit: SPDT
200μA Supply Current
DG333ALDW-E3 Applications
There are a lot of Vishay Siliconix DG333ALDW-E3 Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- PDH Multiplexers
- Isolation
- ATM
- Channelized and Unchannelized DS3 applications
- Low-Voltage
- Audio and video routing
- Cross Connects
- Residential Gateways, Home Gateway/Router
- Microprocessor controlled systems