DG2743DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 8Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2743 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 81pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 30ns, 28ns |
| Charge Injection | 5.8pC |
| Crosstalk | -89dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Drain to Source Resistance | 800mOhm |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2743DQ-T1-E3 Overview
Due to its 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, there are 8 terminations. As a result of its 1 channels, this electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 8 pins. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Use DG2743 to search for variants of the digital switches. A 8Ohm internal resistance characterizes this multiplexer. You can find the functions of the 8 pins in the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. A low voltage of 1.5V should be applied to the electronic component. The analogue multiplexer could operate on 10nA current. The voltage required by this switch device is 1.5V~3.6V, draining from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. A voltage of 3V can be used to operate the electronic component. Operating the 2 inputs requires 2 inputs. Additional features of the electronic component include: VIDEO APPLICATION. There is 800mOhm Drain to Source resistance on this electronic part.
DG2743DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
10nA Supply Current
Additional Features: VIDEO APPLICATION
Drain-to-Source resistance: 800mOhm
DG2743DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2743DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Medical systems
- Imaging
- T1/E1 Terminals
- Relay Replacement
- Microprocessor Controlled Analog Systems
- Battery Powered Systems
- SONET
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Data switching