DG2613DX-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-563, SOT-666 |
| Number of Pins | 6 |
| Weight | 32.006612mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.4Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 172mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | FLAT |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2613 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Power Dissipation | 172mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 60 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 35 ns |
| On-State Resistance (Max) | 1.4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 36pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 60ns, 35ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω (Max) |
| Crosstalk | -73dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 37ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 600μm |
| Length | 1.7mm |
| Width | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2613DX-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a SOT-563, SOT-666. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. Total terminations are 6. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. This electrical component is included in the 6 series of products. Based on SPDT switching circuits, these analog multiplexers work. Use DG2613 to search for variants of the digital switches. An switch multiplexer with 1.4Ohm internal resistance has a value of 1.4Ohm. Datasheets for functions of 6 pins are available. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 1.8V. In order to operate this switch device, it would need a current of 10nA. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. A 1 input needs to be operated. In this digital multiplexer, there are 2 outputs.
DG2613DX-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG2613DX-T1-E3 Applications
There are a lot of Vishay Siliconix DG2613DX-T1-E3 Analog Switches & Multiplexers ICs applications.
- SDH
- Cable PC
- Battery Powered Systems
- Cell phones
- Microprocessor controlled systems
- Wireless Local Loop
- High-Voltage
- Multiplexers
- Automatic test equipment
- Audio/video switches