DG2301DL-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 20Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2301 |
| Pin Count | 5 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.5 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 4.2 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 10μA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 3.9ns, 4ns |
| Voltage - Supply, Single (V+) | 4V~5.5V |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2301DL-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. 5 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 5 pins. Multiplexers built on a SPST - NO switching circuit are built. Circuits number 1 make up this analogue multiplexer. DG2301 can be used to search for analog multiplexer variants. An switch multiplexer with 20Ohm internal resistance has a value of 20Ohm. For details about the functions of 5 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. A cost-effective Single supply type analogue multiplexer. A low voltage of 4V should be applied to the electronic component. For this digital switch to work, 10nA current would suffice. A voltage of 4V~5.5V is required for this switch device, which drains from a single voltage source. Put voltage above 1μA on the multiplexer to cause damage.
DG2301DL-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
DG2301DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2301DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- PCMCIA cards
- Communications systems
- ATM
- PBXs
- Wireless Local Loop
- Intelligent PBX
- Sample-and-hold systems
- Precision data acquisition
- Battery Powered Instruments