DG2032DN-T1-E4
| Parameters | |
|---|---|
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-VFQFN Exposed Pad |
| Number of Pins | 12 |
| Weight | 21.99923mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| Resistance | 5Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.295W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2032 |
| Pin Count | 12 |
| Number of Outputs | 4 |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Power Dissipation | 1.295W |
| Max Supply Current | 1μA |
| Turn On Delay Time | 53 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 38 ns |
| On-State Resistance (Max) | 5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 15pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 53ns, 38ns |
| Charge Injection | 38pC |
| Channel-to-Channel Matching (ΔRon) | 400m Ω (Max) |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 900μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG2032DN-T1-E4 Overview
Shipping overseas is convenient due to the electrical component's packing in 12-VFQFN Exposed Pad. High reliability is provided by advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. In total, there have been 12 terminations. A high-quality output is provided by the electrical component's 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. As part of its design, the 12 series is equipped with this electronic component. Unlike digital switches, these are based on SPDT switching circuits. Try searching with DG2032 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 5Ohm. For functions related to 12 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The digital multiplexer has a low cost Single supply. 1.8V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 10nA current. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There are 2 inputs to be operated. This digital multiplexer has 4 outputs.
DG2032DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG2032DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2032DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Low-Voltage
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial and process control systems
- Public switching systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Switching Systems
- Audio signal routing
- RGB switches
- Mechanical reed relay replacement