CY74FCT2374ATSOCG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74FCT |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74FCT2374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 250MHz |
| Propagation Delay | 6.5 ns |
| Turn On Delay Time | 2 ns |
| Family | FCT |
| Current - Quiescent (Iq) | 200μA |
| Output Characteristics | 3-STATE WITH SERIES RESISTOR |
| Current - Output High, Low | 15mA 12mA |
| Max Propagation Delay @ V, Max CL | 6.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | ROHS3 Compliant |
CY74FCT2374ATSOCG4 Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. A package named Tubeincludes it. This output is configured with Tri-State, Non-Inverted. JK flip flop uses Positive Edgeas the trigger. The electronic part is mounted in the way of Surface Mount. A voltage of 4.75V~5.25Vis used as the supply voltage. Currently, the operating temperature is -40°C~85°C TA. The type of this D latch is D-Type. In terms of FPGAs, it belongs to the 74FCT series. In order for it to function properly, its output frequency should not exceed 250MHz. In total, it contains 1 elements. T flip flop consumes 200μA quiescent energy. The number of terminations is 20. D latch belongs to the 74FCT2374 family. Power is provided by a 5V supply. A JK flip flop with a 5pFfarad input capacitance is used here. It belongs to the family of electronic devices known as FCT. In this case, the electronic component is mounted in the way of Surface Mount. This board has 20 pins. In this device, the clock edge trigger type is Positive Edge. The RS flip flops belongs to FF/Latches base part number. It is designed with 8bits. There is a 5.25Vmaximum supply voltage (Vsup). If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 4.75V. A total of 5V power supplies are needed to run it. This D flip flop is equipped with 0 ports. There are 8 output lines in this JK flip flop.
CY74FCT2374ATSOCG4 Features
Tube package
74FCT series
20 pins
8 Bits
5V power supplies
CY74FCT2374ATSOCG4 Applications
There are a lot of Texas Instruments CY74FCT2374ATSOCG4 Flip Flops applications.
- Divide a clock signal by 2 or 4
- Data transfer
- Communications
- Bounce elimination switch
- Convert a momentary switch to a toggle switch
- Clock pulse
- CMOS Process
- Balanced 24 mA output drivers
- Safety Clamp
- EMI reduction circuitry