CD74HCT109MT
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74HCT |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| Type | JK Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74HCT109 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 4mA |
| Clock Frequency | 54MHz |
| Propagation Delay | 40 ns |
| Turn On Delay Time | 17 ns |
| Family | HCT |
| Logic Function | AND, Flip-Flop, JK-Type |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 4mA 4mA |
| Max I(ol) | 0.004 A |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 40ns @ 4.5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 9.9mm |
| Width | 3.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
CD74HCT109MT Overview
In the form of 16-SOIC (0.154, 3.90mm Width), it has been packaged. It is contained within the Tape & Reel (TR)package. The output it is configured with uses Differential. JK flip flop uses Positive Edgeas the trigger. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis used as the supply voltage. In the operating environment, the temperature is -55°C~125°C TA. A flip flop of this type is classified as a JK Type. In FPGA terms, D flip flop is a type of 74HCTseries FPGA. Its output frequency should not exceed 54MHz. T flip flop consumes 4μA quiescent energy. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is a member of the 74HCT109 family. It is powered from a supply voltage of 5V. Its input capacitance is 10pF farads. An electronic device belonging to the family HCTcan be found here. Surface Mount mounts this electronic component. A total of 16pins are provided on this board. Its clock edge trigger type is Positive Edge. It is included in FF/Latches. Its flexibility is enhanced by 2 circuits. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. The D latch runs on a voltage of 5V volts. High efficiency requires the supply voltage to be maintained at 5V. With a current output of 4mA , it offers maximum design flexibility.
CD74HCT109MT Features
Tape & Reel (TR) package
74HCT series
16 pins
5V power supplies
CD74HCT109MT Applications
There are a lot of Texas Instruments CD74HCT109MT Flip Flops applications.
- Single Down Count-Control Line
- Buffer registers
- 2 – Bit synchronous counter
- CMOS Process
- Test & Measurement
- Common Clocks
- Count Modes
- Frequency Divider circuits
- Circuit Design
- Memory