CD74HC107M96E4
| Parameters | |
|---|---|
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 14 |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -55°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 4.5V |
| Frequency | 60MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Temperature Grade | MILITARY |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 5.2mA |
| Number of Bits | 2 |
| Propagation Delay | 170 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 14 ns |
| Family | HC/UH |
| Logic Function | Flip-Flop, JK-Type |
| Logic IC Type | J-K FLIP-FLOP |
| Max I(ol) | 0.006 A |
| High Level Output Current | -5.2mA |
| Low Level Output Current | 5.2mA |
| Schmitt Trigger | No |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Negative Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
CD74HC107M96E4 Overview
SOICis the way it is packaged. The Tape & Reel (TR)package contains it. D latch consists of 2 elements. 14terminations have occurred. It is powered from a supply voltage of 4.5V. HC/UHis the family of this D flip flop. There is an electronic part that is mounted in the way of Surface Mount. There are 14pins on it. It has a clock edge trigger type of Negative Edge. The part you are looking for is included in FF/Latches. This flip flop is designed with 2 Bits. Considering its reliability, this T flip flop is well suited for TR. There are 1 output lines on it. Quiescent current is consumed by the D latch in the amount of 4μA. A -5.2mAis set for the high level output current. There is no low level output current set at 5.2mA. If the operating temperature is lower than 125°C, it is recommended. A temperature above -55°Cshould be used for the operation. It is powered by 2V as its minimum supply voltage. In this case, it supports a maximum supply voltage of 6V. A frequency of 60MHzcan be achieved. It uses J-K FLIP-FLOPas its logic IC. As a result, it is equipped with 2 functions . This device is equipped with a pin count of 14. This flip flop features a maximum design flexibility due to its output current of 5.2mA.
CD74HC107M96E4 Features
Tape & Reel (TR) package
14 pins
2 Bits
2 Functions
14 pin count
CD74HC107M96E4 Applications
There are a lot of Texas Instruments CD74HC107M96E4 Flip Flops applications.
- Buffer registers
- QML qualified product
- Common Clocks
- High Performance Logic for test systems
- Functionally equivalent to the MC10/100EL29
- Balanced 24 mA output drivers
- Asynchronous counter
- Synchronous counter
- Patented noise
- ESD protection