BTS462TATMA1
| Parameters | |
|---|---|
| Factory Lead Time | 18 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | TO-252-5, DPak (4 Leads + Tab), TO-252AD |
| Surface Mount | YES |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| Series | miniPROFET® |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Terminal Position | SINGLE |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 13.5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | BTS462 |
| Pin Count | 4 |
| JESD-30 Code | R-PSSO-G4 |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | N-Channel |
| Supply Voltage-Max (Vsup) | 34V |
| Supply Voltage-Min (Vsup) | 5V |
| Interface | On/Off |
| Current - Output (Max) | 3.5A |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5V~34V |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 4.4A |
| Rds On (Typ) | 70m Ω |
| Turn Off Time | 230 µs |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Height Seated (Max) | 2.5mm |
| Length | 6.5mm |
| Width | 6.22mm |
| RoHS Status | ROHS3 Compliant |
BTS462TATMA1 Overview
As a result, it is packaged in the form of a Tape & Reel (TR).It is included with the TO-252-5, DPak (4 Leads + Tab), TO-252AD package as well.This LED driving board is mounted using the mounting type Surface Mount.This switch is of type General Purpose.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.The LED driver has 1 outputs.The LED driving board is powered by a voltage of Not Required.It has a maximum output voltage of N-Channel volts.A lighting driver with Auto Restart features is available.As you can see, it comes from the BTS462 family.It contains 4 terminations.It is important to note that the LED driving board has 1 functions.The maximum output of the LED driving board is 3.5AV.Using a voltage of 13.5V allows for high efficiency.4 pins are equipped with it.There is an electrical component included in the miniPROFET? series.The lighting driver is configured to have a maximum supply voltage of 34V (Vsup).In order to operate normally, the supply voltage (Vsup) must remain above 5V.
BTS462TATMA1 Features
Supplied from 13.5V
BTS462TATMA1 Applications
There are a lot of Infineon Technologies BTS462TATMA1 Power Switches ICs applications.
- Hot Swap
- USB3.1 Power Delivery
- Solid State Drivers
- Portable GPS
- USB Power Distribution
- Storage Drives
- Portable GPS Device
- Hot Swaps
- Notebook PC
- Notebook and Tablet Computers