BD6512F-E2
| Parameters | |
|---|---|
| Factory Lead Time | 14 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.173, 4.40mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -25°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Not For New Designs |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100mOhm |
| Additional Feature | CONTROL LOGIC: ACTIVE HIGH |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 560mW |
| Technology | MOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | BD651* |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Output Voltage | 6.3V |
| Output Type | N-Channel |
| Max Output Current | 600mA |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 3V |
| Interface | On/Off |
| Nominal Supply Current | 85μA |
| Output Configuration | High Side |
| Power Dissipation | 560mW |
| Output Current | 500mA |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Output Power | 560mW |
| Switch Type | USB Switch |
| Min Input Voltage | 2.7V |
| Max Input Voltage | 5.5V |
| Output Current per Channel | 500mA |
| Nominal Input Voltage | 5.5V |
| Ratio - Input:Output | 1:2 |
| Voltage - Load | 3V~5.5V |
| Driver Number of Bits | 2 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Reverse Current, UVLO |
| Turn On Time | 6000 µs |
| Rds On (Typ) | 100m Ω |
| Built-in Protections | OVER CURRENT; OVER VOLTAGE; THERMAL |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD6512F-E2 Overview
The package is in the form of a Tape & Reel (TR).In the 8-SOIC (0.173, 4.40mm Width) package, it is included.It has been mounted as Surface Mount on the LED driver.It owns USB Switch switch type.Keeping the temperature at -25°C~85°C TA ensures reliable operation.The lighting driver is equipped with 2 outputs that can be used.To operate, it needs a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be obtained with this LED driver.This LED driving board is equipped with Status Flag features in order for it to be useful.There is a BD651* family of things that it belongs to.As a result, there are 8 terminations.In order to operate, the 8 pins are used.It is important to note that the LED driving board has 2 functions.To comply with the operation criteria, the maximum output current is reduced to 600mA.With a supply voltage of 5V, high efficiency is possible.It is mounted in the way of Surface Mount.There are 8 pins in total on this board.It has a resistance of 100mOhm.When this is the case, the output current is set to 500mA.A self-contained econtainer holding Peripheral Drivers capacity contains this lighting driver.In order to operate normally, the supply voltage (Vsup) must be maintained above 3V.There is a voltage supply of 5V volts on this part.This LED driver can handle voltages up to 5.5V volts.As a minimum input voltage, it requires 2.7V volts.By using this lighting driver, it is also possible to produce CONTROL LOGIC: ACTIVE HIGH.
BD6512F-E2 Features
Supplied from 5V
Resistance of 100mOhm
Additional features like CONTROL LOGIC: ACTIVE HIGH
BD6512F-E2 Applications
There are a lot of ROHM Semiconductor BD6512F-E2 Power Switches ICs applications.
- Wireless Modem Data Cards
- Portable GPS Device
- PC Card Hot Swap
- Hot-Swap Systems
- Notebook and Tablet Computers
- Wearable Devices
- Solid State Drivers
- Set-top-box
- Set-Top Boxes
- Low Voltage I/O System Power