BD6226FP-E2
| Parameters | |
|---|---|
| Factory Lead Time | 9 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs |
| Number of Pins | 25 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 25 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Applications | DC Motors, General Purpose |
| Subcategory | Motion Control Electronics |
| Technology | Power MOSFET |
| Voltage - Supply | 6V~15V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Terminal Pitch | 0.8mm |
| Frequency | 100kHz |
| Base Part Number | BD622* |
| Pin Count | 25 |
| Output Voltage | 18V |
| Supply Voltage-Max (Vsup) | 15V |
| Supply Voltage-Min (Vsup) | 6V |
| Number of Channels | 2 |
| Interface | Logic |
| Analog IC - Other Type | BRUSH DC MOTOR CONTROLLER |
| Nominal Supply Current | 2mA |
| Output Configuration | Half Bridge (4) |
| Output Current | 1A |
| Max Output Voltage | 18V |
| Output Current per Channel | 1A |
| Supply Current-Max (Isup) | 3.5mA |
| Voltage - Load | 6V~15V |
| Fault Protection | Current Limiting, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 1.5 Ω |
| Drain to Source Resistance | 1.5Ohm |
| Load Type | Inductive |
| Length | 13.6mm |
| Width | 5.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
BD6226FP-E2 Overview
Tape & Reel (TR) is used for packaging.H bridge is included in the 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs package as a cost-saving measure.Bridge driver is possible to improve the reliabilbridge drivery of 6V~15V by increasing the supply voltage.There is a mounting of H bridge circuit in Surface Mount.Motor driver H bridge is possible for -40°C~85°C TA to operate normally at motor driver H bridges operating temperature.H bridge motor driver is pretty useful in a wide range of applications, including DC Motors, General Purpose.Surface Mount is adopted as a technique to mount H gate on the PCB.It is possible to terminate a transmission line with a 25 termination using the H bridge which matches the characteristic impedance of the transmission line.Signal interfaces include 25 pins that serve as pronged contacts.Its base H bridge ic number, BD622*, can be used to locate other H bridge ics that are related.This H bridge operates with a voltage of 12V.The analog IC type of this H bridge is BRUSH DC MOTOR CONTROLLER.As a result of the current flowing through the output and power supply pins, there is a current of 1A.A bridge driver's 25 pins work together in order to perform its specific functions.This H bridge motor driver belongs to the subcategory of Motion Control Electronics and shares several similarities with other parts in that category.In this case, the voltage released by the Hbridge is 18V.
BD6226FP-E2 Features
Available in 25-SOP (0.213, 5.40mm Width) + 2 Heat Tabs Package / Case
Operating Temperature at the range of Surface Mount
Interface IC Type : BD622*
BD6226FP-E2 Applications
There are a lot of ROHM Semiconductor BD6226FP-E2 Full Bridge Drivers, Half-Bridge Drivers applications.
- Non-V-Core
- CD players
- High-Performance Gaming Motherboards
- Home Appliances
- Small Form-Factor Voltage Regulator Modules
- Bipolar stepper motor
- Compact Blade Servers
- PC peripherals
- Voltage Regulators
- High current, low profile DC-DC converters