ALD2332ASAL
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| Published | 2010 |
| Series | EPAD® |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Type | General Purpose |
| Max Power Dissipation | 600mW |
| Reach Compliance Code | unknown |
| Pin Count | 8 |
| Output Type | CMOS, NMOS, Push-Pull, TTL |
| Number of Elements | 2 |
| Number of Channels | 3 |
| Nominal Supply Current | 500μA |
| Output Current | 50mA |
| Max Supply Current | 500μA |
| Propagation Delay | 400 ns |
| Quiescent Current | 500μA |
| Response Time | 1.1 μs |
| Common Mode Rejection Ratio | 75 dB |
| Voltage - Supply, Single/Dual (±) | 4V~10V ±2V~5V |
| Input Offset Voltage (Vos) | 500μV |
| Voltage Gain | 103.52dB |
| Power Supply Rejection Ratio (PSRR) | 75dB |
| Max Input Current | 20pA |
| Input Bias Current | 20pA |
| Voltage - Input Offset (Max) | 0.5mV @ 5V |
| Current - Input Bias (Max) | 20pA @ 5V |
| CMRR, PSRR (Typ) | 80dB CMRR, 75dB PSRR |
| Current - Output (Typ) | 50mA @ 5V |
| RoHS Status | ROHS3 Compliant |
ALD2332ASAL Overview
For convenience, it is packaged in 8-SOIC (0.154, 3.90mm Width) .This comparator is of the CMOS, NMOS, Push-Pull, TTL output type.The part is shipped by Tube .A comparator of this type is typically of type General Purpose .In total, it contains 2 elements.The device is equipped with 8 pins.The recommended mounting type is Surface Mount .As a precaution, it is recommended to set the operating temperature to 0°C~70°C to prevent malfunctions.8 pins are present on the comparator.A quiescent current of 500μA is observed in this comparator.There is a Surface Mount for mounting it on a PCB or other board.Normal operation of the device requires a nominal supply current of 500μA .A supply current exceeding 500μA may result in the comparator malfunctioning.Electronic comparator is possible to input a maximum of 20pA current into the device.The voltage formula shows that the part has a voltage gain of 103.52dB .The output quality of 3 channels is maintained by cooperating with each other.Comparator electronics comes from the series of EPAD? comparator parts.
ALD2332ASAL Features
CMOS, NMOS, Push-Pull, TTL output capability
General Purpose IC
Employing 2 elements
Operates under 0°C~70°C
Quiescent Current: 500μA
Voltage Gain: 103.52dB
ALD2332ASAL Applications
There are a lot of Advanced Linear Devices Inc. ALD2332ASAL linear comparators applications.
- Security Detection Systems
- Wireless Base Stations
- Notebooks and PDAs
- General-Purpose, Low-Voltage Applications
- Hand-Held Electronics
- Power Supervision
- Battery management and protection
- Ultra-Low Power Systems
- Analog front end
- Threshold Detectors