ADP195ACBZ-R7
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 4-UFBGA, WLCSP |
| Number of Pins | 4 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Feature | Slew Rate Controlled |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 4 |
| ECCN Code | EAR99 |
| Resistance | 100mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 360μW |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADP195 |
| Pin Count | 4 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1.1A |
| Operating Supply Voltage | 3.6V |
| Voltage | 3.6V |
| Interface | On/Off |
| Operating Supply Current | 5μA |
| Current | 200mA |
| Output Configuration | High Side |
| Power Dissipation | 360μW |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 1.1V |
| Max Input Voltage | 3.6V |
| Nominal Input Voltage | 3.6V |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 1.1V~3.6V |
| Driver Number of Bits | 1 |
| Fault Protection | Reverse Current |
| Rds On (Typ) | 50m Ω |
| Height | 370μm |
| Length | 1.07mm |
| Width | 990μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADP195ACBZ-R7 Overview
It is package in Tape & Reel (TR) case.In the 4-UFBGA, WLCSP package, it is included.It has been mounted as Surface Mount on the LED driver.The switch type of this switch is General Purpose.The temperature should be set to -40°C~125°C TJ to ensure reliable functioning.In this LED driver, there are no outputs available.It uses a supply voltage of Not Required to operate.It has a maximum output voltage of P-Channel volts.A lighting driver with Slew Rate Controlled features is available.It comes under the family of ADP195.In total, there are 4 terminations.For operation, 4 pins are used.There are 1 functions of the LED driver.The maximum output current is reduced to 1.1A to meet the operation criteria.With a supply voltage of 1.8V, high efficiency is possible.The LED driving board is mounted in the way of Surface Mount.This LED driver is equipped with a total of 4 pins.Currently, the LED driving board has 100mOhm resistance.A container with a capacity of Peripheral Drivers contains this self-contained lighting driver.In order to achieve the best efficiency, the supply voltage should be set to 3.6V.As far as input voltage goes, its maximum is 3.6V volts.There is a minimum input voltage of 1.1V volts.
ADP195ACBZ-R7 Features
Supplied from 1.8V
Resistance of 100mOhm
ADP195ACBZ-R7 Applications
There are a lot of Analog Devices Inc. ADP195ACBZ-R7 Power Switches ICs applications.
- Low Voltage I/O System Power
- Portable Devices
- Portable/Handheld Devices
- Storage (HDDs, SSDs)
- Portable GPS Device
- Solid-State Drives
- Various applications equipped with buttons
- USB Protection
- Portable GPS
- USB Power Distribution