ADG822BRMZ
| Parameters | |
|---|---|
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 67ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG822 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 24MHz |
| Turn-Off Delay Time | 16 ns |
| On-State Resistance (Max) | 600mOhm |
| High Level Output Current | 200mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
ADG822BRMZ Overview
The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~125°C TA degrees Celsius. Total terminations are 8. Due to its 2 channels, the electrical component produces high-quality output. Powered by a 3.6V voltage supply, the electrical part should be switched on and run. As part of its design, the 8 series is equipped with this electronic component. A SPST - NC switching circuit is used for these analog switches. Try searching with ADG822 if you're looking for variants. This digital multiplexer has 600mOhm internal resistance. Datasheets for functions of 8 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 1.8V should be applied to the electronic component. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. If you put voltage higher than 2μA on the digital multiplexer, damage may occur. A 24MHz-bandwidth can be used for data transfer.
ADG822BRMZ Features
2 Channels
Switch Circuit: SPST - NC
Bandwidth: 24MHz
ADG822BRMZ Applications
There are a lot of Analog Devices Inc. ADG822BRMZ Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Avionics
- Power routing
- Switching Systems
- USB 1.1 signal switching circuits
- Microwave transmission systems
- Access Concentrators
- MP3 players
- PDAs
- Communication systems