ADG822BRM
| Parameters | |
|---|---|
| Surface Mount | YES |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Terminal Finish | TIN LEAD |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| JESD-30 Code | S-PDSO-G8 |
| Supply Voltage-Max (Vsup) | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| -3db Bandwidth | 24MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switch-on Time-Max | 67ns |
| Switch-off Time-Max | 18ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
ADG822BRM Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~125°C TA is the extended operating temperature. 8 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. A 3.6V voltage supply should turn on and run the electronic component. An injection of 8 pins is performed into the body of the electrical component. A SPST - NC switching circuit is used to build these analog multiplexers. Circuits number 2 make up this analogue multiplexer. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply.
ADG822BRM Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 24MHz
ADG822BRM Applications
There are a lot of Rochester Electronics, LLC ADG822BRM Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Audio/video switches
- Intelligent PBX
- Data Acquisition Systems
- Cross Connects
- Audio and video routing
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- T1/E1 Terminals
- Precision instrumentation
- Remote wireless modules