ADG821BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 3.6V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG821 |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| -3db Bandwidth | 24MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 85pF 98pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 160m Ω |
| Crosstalk | -82dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 67ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG821BRM-REEL Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~125°C TA. 8 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. If the voltage supply is 3.6V volts, the electrical component should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with ADG821 if you're looking for variants. Analog switches have 600mOhm internal resistance. Datasheets for functions of 8 pins are available. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 1.8V. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 2μA.
ADG821BRM-REEL Features
2 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 24MHz
ADG821BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG821BRM-REEL Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Cross Connects
- Audio and video routing
- PBX interfaces
- Avionics and Military Systems
- Routers
- Isolation
- Intelligent PBX
- Audio/video switches
- Medical systems