ADG819BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 600mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG819 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 2μA |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 16 ns |
| -3db Bandwidth | 17MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 80pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 16ns |
| Charge Injection | 20pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -72dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG819BRM-REEL Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. There are 8 terminations totally. A 1 channel electronic part produces high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. These analog multiplexers are built based on SPDT switching circuits. A total of 1 circuits make up this switch device. Using the ADG819 search parameter, you can discover variants of the switch. An switch multiplexer with 600mOhm internal resistance has a value of 600mOhm. The datasheets for the 8 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. A low voltage of 1.8V should be applied to the electronic component. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. A voltage higher than 2μA may cause damage to the switch multiplexer.
ADG819BRM-REEL Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 17MHz
ADG819BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG819BRM-REEL Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Remote wireless modules
- Battery Powered Systems
- ISDN NT1/TA
- Medical
- Medical systems
- New designs requiring multiplexer functions
- DVD-R
- Channel Banks
- Microprocessor Controlled Analog Systems