ADG813YRU-REEL
| Parameters | |
|---|---|
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 5 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 650mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF 35pF |
| On-state Resistance Match-Nom | 0.04Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 25ns, 5ns |
| Charge Injection | 30pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 8ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 14.4μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG813 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 1.8/3.3V |
| Number of Channels | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Power Dissipation | 14.4μW |
| Max Supply Current | 4μA |
| Throw Configuration | SPST |
ADG813YRU-REEL Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~125°C TA is the extended operating temperature. In total, there are 16 terminations. The electronic part provides high-quality output because it has 4 channels. Turning on and running the electrical part should be easy with a 2.5V voltage supply. The electrical component body receives 16 pins. The analog switch ics are built using SPST - NO/NC switching circuits. Use ADG813 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 650mOhm. You can find the functions of the 16 pins in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 3.6V. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. Analogue multiplexers require a 1.65V~3.6V voltage to drain from a single voltage supply. A voltage higher than 4μA may cause damage to the switch multiplexer. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
ADG813YRU-REEL Features
4 Channels
Switch Circuit: SPST - NO/NC
-3db Bandwidth: 90MHz
ADG813YRU-REEL Applications
There are a lot of Analog Devices Inc. ADG813YRU-REEL Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- High reliability control systems
- Switching Systems
- Modems
- Data Acquisition Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
- Avionics test equipment
- Automatic test equipment
- 65 V DACs