ADG802BRT-REEL
| Parameters | |
|---|---|
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG802 |
| Pin Count | 6 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
ADG802BRT-REEL Overview
Presented in SOT-23-6, this electrical component is convenient for overseas shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there have been 6 terminations. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. The electronic part body is injected with 6 pins. These analog multiplexers are built based on SPST - NC switching circuits. It consists of 1 circuits. ADG802 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 300mOhm. Please refer to the datasheets for 6 pins functions. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.8V. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA.
ADG802BRT-REEL Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 12MHz
ADG802BRT-REEL Applications
There are a lot of Analog Devices Inc. ADG802BRT-REEL Analog Switches & Multiplexers ICs applications.
- Data switching
- Mechanical reed relay replacement
- Transmit
- Medical systems
- Battery Powered Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Industrial control systems
- Wireless Local Loop
- HDTV
- SDH