ADG802BRMZ
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG802 |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 12MHz |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NC |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG802BRMZ Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). To ensure high reliability, a new packaging method Tube is used. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~125°C TA is the extended operating temperature. A total of 8 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 3V voltage supply. This electrical component is included in the 8 series of products. Unlike digital switches, these are based on SPST - NC switching circuits. ADG802 can be used to search for analog multiplexer variants. A 300mOhm internal resistance characterizes this multiplexer. Datasheets for functions of 8 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. There should be 1.8V voltage fed to the electrical part below 1.8V. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to transfer data over a 12MHz-bandwidth.
ADG802BRMZ Features
1 Channels
Switch Circuit: SPST - NC
Bandwidth: 12MHz
ADG802BRMZ Applications
There are a lot of Analog Devices Inc. ADG802BRMZ Analog Switches & Multiplexers ICs applications.
- SONET
- Multi-Line E1 Interface Cards
- High-Voltage
- ISDN NT1/TA
- Microwave transmission systems
- SDH/SONET multiplexers
- SDH
- Cellular phones
- Access Concentrators
- MP3 players