ADG801BRTZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 8 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Surface Mount | YES |
| Number of Pins | 6 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG801 |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 12MHz |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG801BRTZ-REEL7 Overview
As the electronic part is packed in SOT-23-6, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around -40°C~125°C TA. Total terminations are 6. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 6 pins. Unlike digital switches, these are based on SPST - NO switching circuits. ADG801 can be used to search for analog multiplexer variants. There is 300mOhm internal resistance in this digital multiplexer. For details about the functions of 6 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1nA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. A digital multiplexer may suffer damage if voltage is applied above 1μA. There are various bandwidths available for data transfer.
ADG801BRTZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 12MHz
ADG801BRTZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG801BRTZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Data switching
- Cell phones
- Cable PC
- Audio/video switches
- RGB switches
- Optical Applications
- 65 V DACs
- Avionics and Military Systems
- Audio signal routing
- Channel Banks