ADG801BRMZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 20 Weeks |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG801 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 12MHz |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG801BRMZ-REEL7 Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~125°C TA. The total number of terminations is 8. The electronic part provides high-quality output because it has 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. Multiplexers built on a SPST - NO switching circuit are built. ADG801 can be used to search for analog multiplexer variants. There is 300mOhm internal resistance in this digital multiplexer. The datasheets for the 8 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Digital switch that provides Single power at a cost-effective price. 1.8V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1nA would be sufficient for this switch device. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. The transfer of data can be performed over 12MHz bandwidths.
ADG801BRMZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 12MHz
ADG801BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG801BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- ISDN NT1/TA
- High-Voltage
- Signal routing between systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- CSU
- Microwave transmission systems
- Routers
- Audio/video switches
- Relay Replacement