ADG801BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 300mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG801 |
| Pin Count | 8 |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 12MHz |
| On-State Resistance (Max) | 300mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 180pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 45ns, 15ns |
| Charge Injection | 50pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG801BRM-REEL Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there are 8 terminations. This electronic part offers high-quality output due to its 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 8 series. Multiplexers built on a SPST - NO switching circuit are built. ADG801 can be used to search for analog multiplexer variants. An switch multiplexer with 300mOhm internal resistance has a value of 300mOhm. Datasheets for functions of 8 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analog switch ics with Single supply type are cost-effective. 1.8V is the lowest voltage the electrical component should receive. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. A digital multiplexer may suffer damage if voltage is applied above 1μA.
ADG801BRM-REEL Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 12MHz
ADG801BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG801BRM-REEL Analog Switches & Multiplexers ICs applications.
- Cell phones
- Remote wireless modules
- CSU
- Cable Modem
- E1 Multiplexer
- Private Branch Exchange (PBX)
- Audio and video switching
- E1 Network Equipment
- ATM
- Battery Powered Systems