ADG728BRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Subcategory | Multiplexers or Switches |
| Max Power Dissipation | 100μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG728 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 8 |
| Interface | 2-Wire, Serial |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Analog IC - Other Type | AUDIO/VIDEO SWITCH |
| Operating Supply Current | 10μA |
| Power Dissipation | 100μW |
| Max Supply Current | 20μA |
| Number of Bits | 8 |
| Throw Configuration | DPST |
| Turn On Delay Time | 130 ns |
| Bandwidth | 65MHz |
| Turn-Off Delay Time | 115 ns |
| On-State Resistance (Max) | 4.5Ohm |
| High Level Output Current | 120mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 13pF 85pF |
| On-state Resistance Match-Nom | 0.4Ohm |
| Switch Time (Ton, Toff) (Max) | 95ns, 85ns (Typ) |
| Charge Injection | 3pC |
| Crosstalk | -75dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Voltage - Supply, Single (V+) | 2.7V~5.5V |
| Height | 1.05mm |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG728BRU Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. Surface Mount is where this multiplexer is located. 8:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. In total, 16 terminations have occurred. The electronic part provides high-quality output because it has 8 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. An electrical component like this is included in the 16 series. There are 1 circuits in this multiplexer. Search with ADG728 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 4.5Ohm. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexers or Switches. Users should never supply a voltage higher than 5.5V to a switch device. There should be 2.7V voltage fed to the electrical part below 2.7V. This multiplexer would work with 10μA current. This analog switch requires a voltage of 2.7V~5.5V to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 20μA. A AUDIO/VIDEO SWITCH analog IC is integrated into the board. It is possible to transfer data over a 65MHz-bandwidth. Its conductivity is 8-bit.
ADG728BRU Features
8 Channels
10μA Supply Current
Bandwidth: 65MHz
8-Bit
ADG728BRU Applications
There are a lot of Analog Devices Inc. ADG728BRU Analog Switches & Multiplexers ICs applications.
- Relay replacements
- Video switching
- Cable PC
- Channel Banks
- Audio and video switching
- Mechanical reed relay replacement
- Cell phones
- Medical
- SDH/SONET multiplexers
- Intelligent PBX